How To Fix Juul Contact Pin Pushed In

Why Would I Want to Perform a JUUL Disassembly?

Well…  At that place'southward a scattering of reasons one would want to learn how to take apart the JUUL.

Sometimes the JUUL can experience issues, and occasionally these issues result in your JUUL ceasing to work entirely.

This usually happens when one neglects toregularly clean their JUUL.

Curt of requesting a replacement and waiting for a new bombardment to be shipped out, our only option at this bespeak is to take apart the JUUL and see if we can fix information technology ourselves through cleaning the internal components.

Another reason could exist to access a ill and unique fashion to personally customize your JUUL.

The final reason one would wish to detach their JUUL is out of simple curiosity. (Shoutout to all the tinkerers reading this!)

However, we all know what that dastardly character "marvel" does to our feline friends, and this procedure is no exception.

Out of all the JUUL hacks I propose here, this one definitely comes with the virtually risks and potential side effects associated with it.

CAUTIONS AND CONCERNS

I wouldn't exist a very good doctor if I didn't brand all the risks completely known pre-op.  Acquit with me, I'll brand this quick.

For starters, this process is moderately hard.  If yous don't like taking autonomously things that were designed to be difficult to take apart, this may non be the project for you lot.

Which leads to my next point. The creators of the JUUL would much rather you transport in your defective battery for replacement rather than attempting to fix it yourself.  To this stop, any detected signs of tampering could result in the voiding of your replacement warranty.

If yous are sure your JUUL is dead and would like to claim your warranty then do not effort this process.

Finally, there are some negative side effects that MAY incur mail service-op.  These include but are not express to:

• Voided warranty
• Loose innards upon reassembly
• Poor battery connection
• JUUL death
• Damaged LED

I programme on creating a post with solutions to some of these bug in the near time to come, and then stay tuned for that.

Now that y'all know what you lot're potentially getting yourself into, let's begin the operation.

THE DISASSEMBLY PROCEDURE

Materials Required:

• Narrowly pointed object (Like these great electronics tweezers. Very handy!)
• Sturdy blunt ended object (narrow enough to fit in the JUUL pod opening and sturdy plenty to push out internal components)

Both of these should be hands found around the house, but in case yous want a pair of the tweezers I employ (they are EXTREMELY useful) click the link to a higher place to get yourself a pair!

1.) Printing the LED light out of the metal casing.

The chief connexion point that holds the JUUL together is the tiny plastic circle that covers the LED activation light.  To allow the removal of inner components we must press that plastic down into the device so that it no longer sits flush with the outer metallic body.

This is really the only difficult step of the performance, every bit quite a bit of force is required to push that LED plastic down enough to be articulate of the metal opening.

A.) Using the narrowly pointed object press the light into the device and slightly downwards (towards the charging port)

I used narrow-tipped tweezers, just whatever sturdy object with a betoken smaller than the LED plastic should work fine.

B.) While pressing the light, take the blunt ended object, insert it into the JUUL pod opening and apply house pressure level until the innards begin to slide out, pushing the LED plastic past the metal opening.

While pressing the light in, I used the butt end of some nail clippers as my blunt object to push the innards downwards through the JUUL pod opening.

2.) Push the internal associates through the bottom of the JUUL.

Now that the LED plastic is pushed by its metal opening, it should be fairly easy to slide the innards the remainder of the manner out.

A.) Using the edgeless ended object, button the innards out enough to catch the exposed battery and pull information technology all the way out.

3.) Remove the rubber seal near the pins at the top of the battery.

This rubber seal pops correct off and allows u.s.a. to clean the pins with more ease.  Be careful when removing this piece as the fragile pivot assembly can sometimes be pulled out of place.

iv.) That's it! Yous're JUUL is now fully disassembled.

This is as far as nosotros can get without causing permanent damage to the battery/board connections within the internal assembly.

As you can now see, the JUUL is a beautifully simple device with few individual components.  This keeps the run a risk of malfunction relatively low, which is a expert affair for us JUULers.

If you are performing this operation to attempt to solve functionality issues, then cleaning the disassembled components is your next step.  I outlined just how to do that in this post.

Now, I will explain the quick and easy reassembly process.

How to Reassemble the JUUL

Putting the JUUL back together is much simpler than taking it apart.  Basically, you just repeat the disassembly steps in reverse club, with the exception of having to push the LED out of place.

Annotation: Y'all may desire to trim a flake of the plastic from the LED light to reduce resistance when sliding the internal components back into the metal body.  This is slightly difficult and requires a sharp and narrow pair of pair of scissors.

Here's a pic showing what information technology looks similar after trimming:

1.) Reattach the rubber seal.

Start past pressing the circular part into its pigsty and then positioning the meridian bit over the pins.  Make sure it is connected properly and that the metal pins are unobstructed.

ii.) Insert the internal associates and push it back into place.

Optional Pace:If yous would like to trim some of the LED plastic as mentioned above, at present is the time.

Insert the end with the safe seal into the lesser of the JUUL and push button until the lesser charging port is flush with the metal casing.  Don't forget to brand sure the LED is facing the right fashion!

3.) Ready to Vape!

Pop in a pod and puff away! Your JUUL is now reassembled.

Post-Op Notes

Whatever your reason was for wanting to perform this surgery, I hope everything went smoothly and your desired results were achieved.

If y'all happen to exist experiencing some of the potential negative side furnishings of this handling, I've made a post which direct addresses some of those problems.

And I hope your newly customized JUUL is looking sick. (in the good way, non the doctor fashion)

Likewise remember that JUUL has great customer service, and tin assist solve any problems you may encounter with solutions or a replacement JUUL.

Let me know how this procedure worked out for you!  Did you run into any unexpected problems that I could add to this guide? Possibly a simpler way to go that pesky LED plastic out of the way?  Experience gratuitous to leave whatever thoughts you lot have in the comments below!

I hope you accept a hassle-free day of vaping dear JUULers, we'll come across you soon.

How To Fix Juul Contact Pin Pushed In,

Source: https://thepodprofessor.com/how-to-take-apart-the-juul/

Posted by: mattinglyhouggettere.blogspot.com

Share this post